StudentShare
Contact Us
Sign In / Sign Up for FREE
Search
Go to advanced search...
Free

The Bending of a Cantilever - Lab Report Example

Cite this document
Summary
The measured values of deflection were used to calculate Young’s Modulus (E) of steel. It was found that deflection of a cantilever beam is directly proportional of the…
Download full paper File format: .doc, available for editing
GRAB THE BEST PAPER95.3% of users find it useful
The Bending of a Cantilever
Read Text Preview

Extract of sample "The Bending of a Cantilever"

The paper "The Experiment with the Torsional Pendulum" is a great example of a lab report on physics. The deflection of the cantilever beam has a beam measured by varying load and the length of the cantilever beam. The measured values of deflection were used to calculate Young’s Modulus (E) of steel.  It was found that the deflection of a cantilever beam is directly proportional to the applied load and cube of the length of the cantilever. These measurements provided the value of Young’s modulus of steel to be 203 GPa (Fixed length cantilever) and 174 GPa (Fixed load cantilever). These values are very close to those reported in the literature. The experiment and the calculations are described in this report.

 Objective

The experiment was aimed at measuring Young’s Modulus (E) of a material by measuring the deflection of a cantilever with varying applied load or length of the cantilever.

Theory and Formulae:

A long and thin bar clamped at one end is termed as the cantilever (figure below).

When the load is applied at the free end, it deflects. The vertical deflection of a cantilever subjected to a load W is theoretically given by the formula

                                   

Here, a and b are width and thickness of the bar respectively; L is length and E is Young’s Modulus of the material. Ideally one should incorporate the correction for deflection of the cantilever under its own weight. It may be ignored if the contribution from its weight in the total deflection is small. Thus by measuring the deflection of a cantilever, one can measure Young’s Modulus of the material forming the cantilever.

Materials and Procedure:

Metallic strips of different lengths – 50, 60, 70 and 80 cm and 12.8 mm wide and 4.8 mm thickness were taken as Cantilever. Three different weights of 0.5, 1 and 2 kg were used to cause deflection in the cantilever.

For foxed length 60 cm of the cantilever, the vertical deflection was measured for different weights of 0.5, 1 and 2 kg and the same was recorded. The deflection was plotted vs. the weight and from the slope Young’s Modulus (E) was calculated.

For a fixed weight of 1 kg, the vertical deflection was measured for cantilevers of different lengths – 50, 60, 70 and 80 cm and the same was recorded. The deflection was plotted vs. L3 and from the slope Young’s Modulus (E) was calculated.

Data and Calculations

  • Fixed Length Case

Length of the Cantilever              L = 60 cm = 0.60 m

Width of the Cantilever                a = 12.8 mm = 0.0128 m

Thickness of the Cantilever          b = 4.8 mm = 0.0048 m

Deflection vs. Load Data

Load (kg)

0.5

1

2

Deflection (m)

2*10-2

3.5*10-2

6.5*10-2

 

 

Chart Showing Deflection vs. Load Plot

The slope of the deflection vs. load line is     0.03 m/kg

Therefore, Young’s Modulus (E) will be given by

GPA

Error Analysis:

The first calculation was the slope of the line (m) - d vs W

Error for this (m) will be given as     

Finally, error for the Young’s Modulus E will be given as

           

                       

  • Fixed Load Case

Applied Load                                W = 1 kg

Width of the Cantilever                a = 12.8 mm = 0.0128 m

Thickness of the Cantilever          b = 4.8 mm = 0.0048 m

Deflection vs. Load Data

Length (m)

0.5

0.6

0.7

0.8

Deflection (m)

2*10-2

3*10-2

6*10-2

8*10-2

 

Chart Showing Deflection vs. L3 Plot

The slope of the deflection vs. load line is     0.0162 m/m3

Therefore, Young’s Modulus (E) will be given by

GPA

Error Analysis:

The first calculation was the slope of the line (m) - d vs L3

Error for this (m) will be given as     

Finally, error for the Young’s Modulus E will be given as              

Conclusions:

Based on these experiments it can be concluded that the deflection of a cantilever beam is directly proportional to the applied load and cube of the length of the cantilever. This is a very simple method of finding young’s modulus of a material. The results obtained are very close to the value reported in the literature and different books (~ 210 GPa). This shows how one can use a method as simple as cantilever deflection to measure a very important material property.

Read More
Cite this document
  • APA
  • MLA
  • CHICAGO
(The Bending of a Cantilever Lab Report Example | Topics and Well Written Essays - 750 words, n.d.)
The Bending of a Cantilever Lab Report Example | Topics and Well Written Essays - 750 words. https://studentshare.org/physics/1738080-formal-lab-report-the-bending-of-a-cantilever
(The Bending of a Cantilever Lab Report Example | Topics and Well Written Essays - 750 Words)
The Bending of a Cantilever Lab Report Example | Topics and Well Written Essays - 750 Words. https://studentshare.org/physics/1738080-formal-lab-report-the-bending-of-a-cantilever.
“The Bending of a Cantilever Lab Report Example | Topics and Well Written Essays - 750 Words”. https://studentshare.org/physics/1738080-formal-lab-report-the-bending-of-a-cantilever.
  • Cited: 0 times

CHECK THESE SAMPLES OF The Bending of a Cantilever

Engineering and environmental materials

The third conclusion was that the weight of the proposed cantilever beam of the footway could be adequately and safely supported by the bridge.... STRUCTURAL MECHANICS Name: Course: Tutor: Date: Material selection and structural mechanics of a proposed bridge Executive summary of rapid transit report by Halcrow Engineers Rapid transit report was compiled by Halcrow Group Ltd 2010....
6 Pages (1500 words) Essay

Strength of material 2

a cantilever beam is supported on one end only and must be built into the wall that supports it.... eams: Beams are often classified according to their ideal support conditions as either simply supported beams or cantilever beams.... Two forces act on cantilever beams – firstly, a vertical upward force which supports the weight of the beam and any downward loads and secondly ‘the fixing moment' which prevents the unsupported beam from falling (Eric William Nelson et all, 1997)....
2 Pages (500 words) Essay

Principles of Building Structure

Beams bending strength design is governed by yielding and supported against buckling.... A laterally braced section of a beam has a bending strength, which is the plastic moment Mp.... When the inertia moment about the axis of bending is less or equal to the out of plane inertia moment, lateral-torsional buckling never develops....
8 Pages (2000 words) Essay

Structural engineering

For a simply supported or continuous beam, the clear distance between restraints should be less than or equal to 60bc or 250bc 2/d if less; and for a cantilever with lateral restraint only at support, the clear distance from cantilever to support should be less than or equal to 25bc or 100bc 2/d if less where bc is the breadth of the compression face of the beam and d is the effective depth....
4 Pages (1000 words) Essay

The Welding Technique of Diffusion Bonding

The objective of the following paper is to shed light on the welding method named diffusion bonding, its characteristics, properties, and implied standards of its process.... Additionally, the paper discusses some aspects of applying this technique in practice.... hellip; Diffusion Bonding is a method applied in welding (Solid State) metals and other related materials....
5 Pages (1250 words) Term Paper

De Havilland Comet

It, therefore, needed space for four jet engines that would power the low-wing cantilever.... This paper "De Havilland Comet - the First Produced Commercial Jetliner" focuses on the jetliner that was designed, developed and manufactured by De Havilland at the Hertfordshire headquarters in the United Kingdom....
5 Pages (1250 words) Assignment

Understanding of the Bending Theory

The paper "Understanding of the bending Theory" discusses that the variations between the calculated and the expected values arise from conditions such as inaccuracies in reading and recording values during the experiment, temperature variations, dial gauge malfunctions and even calculation errors.... hen loaded with a uniformly distributed load or a point load, the beam will be subjected to a bending moment.... uch as the amount that a beam will bend when loaded will be determined by the modulus of elasticity of the material, the second moment of the area also determines the degree of deformation in part hence its relevance in the theory of bending....
5 Pages (1250 words) Lab Report

Importance of the Geology for the Construction of the Highway and Associated Structures

"Importance of the Geology for the Construction of the Highway and Associated Structures" paper examines the possible problems that the geology may pose for the construction of the highway and associated structures such as embankments, bridges, or cuttings.... hellip; Many architectural landmarks around the world are made of Limestone....
5 Pages (1250 words) Assignment
sponsored ads
We use cookies to create the best experience for you. Keep on browsing if you are OK with that, or find out how to manage cookies.
Contact Us